Re: netgear wg511t pccard on Clevo m120_w

["felix.schalck" <felix_(_dot_)_schalck_(_at_)_gmx_(_dot_)_net>]

Dana Ferguson wrote:
> Opps forgot the list...
>
> Here is how my Atheros A/B/G card is set up in rc.conf.
>
>
> # -- sysinstall generated deltas -- # Sun Sep 17 13:05:14 2006
> # Created: Sun Sep 17 13:05:14 2006
> # Enable network daemons for user convenience.
> # Please make all changes to this file, not to /etc/defaults/rc.conf.
> # This file now contains just the overrides from /etc/defaults/rc.conf.
> inetd_enable=YES
> nfs_client_enable=YES
> sshd_enable=YES
> nisdomainname="fergus"
> nis_client_enable=YES
> gdm_enable="YES"
> usbd_enable=YES
> hostname=FreeBSD.
> ifconfig_ath0="dhcp ssid Ferguson_Ranch"
> ntpd_enable=YES
> sendmail_enable=YES
> network_interfaces=ath0
>
> Dana
>
>
> On Sat, 2006-10-07 at 18:17 +0200, felix.schalck wrote:
>
>   
> > Lars Engels wrote:
> >     
> > > On Sat, Oct 07, 2006 at 06:05:41PM +0200, felix.schalck wrote:
> > >   
> > >       
> > > > Hi,
> > > >
> > > > I'm trying to get the Netgear wg511t working under 6.x.
> > > > Card works well under linux.
> > > > Dmesg shows:
> > > > --------
> > > > #dmesg | grep card
> > > > cardbus0: <CardBus bus> on cbb0
> > > > pccard0: <16-bit PCCard bus> on cbb0
> > > > ---------
> > > > rc.conf:
> > > > pccard_enable="YES"
> > > > ---------
> > > >
> > > > but when I insert the card: nothing.
> > > >
> > > > What can I do ?
> > > >
> > > > Thanks for help.
> > > >
> > > > Felix
> > > >     
> > > >         
> > > Check, if you have if_ath.ko is loaded (kldstat -v | grep ath)
> > >
> > > Lars
> > >   
> > >       
> > Yauu: that was fast ! Thanks a lot for your response.
> > Yes if_ath loaded:
> >
> > kldstat -v | grep ath
> >                 28 ath_hal
> >                 37 ath_rate
> >                 38 pci/if_ath
> >                 39 cardbus/if_ath
> >
> > What  else can i inverstigate ?
> >
> > Felix
> >     
Thanks for help, but i don't think my problem is a inet config prob.
Trying to find a solution, I enabled cardbus debug.
Here is what I get, when I insert the card:

Status is 0x30000086
Status is 0x30000820
cbb0: card inserted: event=0x00000000, state=30000820
cbb0: cbb_power: 3V
cbb0: cbb_power: 0V

Any ideas from here ?

Thanks a lot,

Felix
> > _______________________________________________
> > freebsd-mobile_(_at_)_freebsd_(_dot_)_org mailing list
> > http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
> > To unsubscribe, send any mail to "freebsd-mobile-unsubscribe_(_at_)_freebsd_(_dot_)_org"
> >     
> _______________________________________________
> freebsd-mobile_(_at_)_freebsd_(_dot_)_org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
> To unsubscribe, send any mail to "freebsd-mobile-unsubscribe_(_at_)_freebsd_(_dot_)_org"
>
>
>   

_______________________________________________
freebsd-mobile_(_at_)_freebsd_(_dot_)_org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "freebsd-mobile-unsubscribe_(_at_)_freebsd_(_dot_)_org"